Adescor Inc.

Contact: Tony Kime

149A Thames Rd
Exeter, ON N6A2L5
Canada

Phone: 519-434-2800
Fax: 519-434-5900

Website

E-mail

Adescor manufacture equipment for the pipe extrusion industry specializing in accessory equipment like cut-offs, tip tables, spinwelders and fabricated fittings equipment.


Adescor have been building high speed cut-off equipment for corrugated pipe since 1994. The first unit was built for cutting 18" - 36" corrugated pipe. Since this first corrugated pipe cut-off Adescor have evolved the range from 4" hi speed units to the largest current design for 60" corrugated pipe.

The pipe cutting systems range in complexity from introductory low speed units for single cutting of corrugated pipe to hi speed servo controlled systems for cutting of integrel bell and spigot pipe with corrugation finder and counting system.

The Adescor designs are based on knife cutting systems with various actuation methods. The knife system is quite, clean and improves the plant environment considerably when compared to traditional circular saw cutting systems. The Adescor units have now been proven on the thickest of corrugated pipes and experimentation is underway for solid wall PE pipes.

The Adescor group have solved hi speed cutting problems for the top corrugated pipe companies in North America. We can offer solutions to companies any where in the world and are happy to design to CE requirements.
 
Spinwelders for belling corrugated pipe

The Adescor group have been building specialized spinwelders for welding bells to corugated pipe since the early 90's.

All Adescor spinwelders use a spinning head to create a friction weld between the pipe length and the pipe bell (socket). The pipe length is clamped to the machine bed, and the bell is attached to the spinning head. Spinwelders are either of the face type, outside diameter type or combination type. Automatic spinwelders are supplied with a conveying system to accept plain end pipe and automatic bell-loading from a feed system. Semi-automatic models require manual loading and unloading of pipe and bells.

For all models machine functions are controlled by a PLC and operator interface panel.The electrical and pneumatic systems can be designed to accommodate specific Customer requirements.

All models can be designed to operate with HDPE or Polypropylene products.
1024 Automatic Outside Diameter Spinwelder (model 1024OD-A)

This machine is designed to automatically weld bells onto corrugated pipe of outside diameter (O.D.) 315mm to 800mm (12.5 ” to 31.5 ”).The weld mechanism is by friction between the outside wall of the pipe and the inside wall of the coupler.

* Set up as an in-line process.
* Fast advance system for pipe feed.
* Automatic bell loading ((operator loads conveyor on an intermittent basis).
* Conveying system accepts pipe from the production line, with bypass capability.
* Automatic discharge of finished product to the client's runout table.
* Minimum full cycle time is 50 seconds.

3-4 Automatic Double Head Outside Diameter Spinwelder (model 34OD-DH-A)

This machine is designed to automatically weld bells onto corrugated double--wall or triple-wall pipe of outside diameter (O.D.) of 75mm (3 ”)and 100mm (4 ”).The weld mechanism is by friction between the outside wall of the pipe and the inside wall of the coupler.

* Bells simultaneously welded to two lengths of pipe per cycle.
* Set up as an in--line process.
* Surge area holds 4 pieces of pipe.
* Automatic bypass when surge area is full.
* Automatic bell loading ((operator loads conveyor on an intermittent basis).
* Conveying system accepts pipe from the production line, with bypass capability.
* Automatic discharge of finished product to the client's runout table.
* Minimum cycle time is 2 pipes per 20 seconds.

410 Semi-automatic Face Weld Spinwelder (model 410FW-SA)

This machine is designed for welding bells to the face (inner sidewall) of pipes of inside diameter 100mm to 250mm (4” to 10”).

* Set up beside the pipe corrugating line or in a separate location.
* Manual loading of pipe lengths to a stationary pipe support.
* Manual loading of bells onto spinning head.
* Automatic pipe trim head.
* Cycle time dependent on operator material handling speed.

210 Automatic Outside Diameter Spinwelder (model 210OD-A)

This machine is designed to automatically weld bells onto plain pipe of outside diameter (O.D.)of 110mm to 300mm (4.33” to 12”). The weld mechanism is by friction between the outside wall of the pipe and the inside wall of the coupler.

* Set up as an in-line process.
* Automatic bell loading (operator loads conveyor on an intermittent basis).
* Conveying system accepts pipe from the production line, with bypass capability.
* Automatic discharge of finished product to the client's runout table.
* Minimum full cycle time is 25 seconds.

416 Automatic Face Weld Spinwelder (model 416FW-A)

This machine is designed for welding bells to the face (inner sidewall) of pipes of inside diameter 100mm to 400mm (4” to 16”).

* Set up as an in-line process.
* Fast advance system for pipe feed.
* Automatic bell loading (operator loads conveyor on an intermittent basis).
* Conveying system accepts pipe from the production line, with bypass capability.
* Automatic discharge of finished product to the client's runout table.
* Pipe trim head included.
* Minimum full cycle time is 20 seconds.

Fittings and Fabrication Equipment

The Adescor group have been building specialized equipment for fabricated fittings for years. Offering hotplate tables, large custom bandsaws, custom diameter holesaws and many other unique devices that are requred in the fabrication shop of a corrugated pipe plant for the production of HDPE pipe accessories such as elbows, tees, end caps and wyes.
42" Hotplate Table (model 442 HPT)

Features:

* Horizontal heated table with non--stick surface.
* Surface is 1220mm x 1520mm (48” x 60”) suitable for 600mm (24”) up to 45 degrees.
* Multiple units can be utilized for larger fittings.
* Optional insulation blankets for heat conservation and protection of the surface.
* Electrical systems can be designed to accomodate specific customer requirements.

36" Fabricated Fittings Bandsaw

Features:

* Easy setup
* Simple manual operation.
* Strap clamp downs to hold pipe
* Variable angle cuts with pre drilled positions for 45's and 22.5's degree cuts.
* Sturdy 3/4" saw blade.
Custom Holes Saws

Features:

* Made to customer specified diameters.
* Can be made to cut through corrugated pipe on a 45 degree angle for drilling reducing wye angle entries
* Arbor can be designed for customer specific radial arm drill.
* Sizes have been built for up to 24" corrugated pipe.